Also 45 degrees are bit lower than what I want.Ĭustom Camera 5 → look front with a little to the bottom to show the trim wheel (personally, I prefer to see the wheel while adjusting the trim to set it visually to certain a position).Ĭustom Camera 8 → copilot view/ a bit closer (zoomed) to MFD/GPS screen Note: there are already dedicated shortcuts for 45 and 120 degrees cockpit quickview in camera views menu, you may use them if you like but I find custom camera better as I can use my free camera while using the custom view ( i.e., I can adjust custom camera when flying). My configuration is as followsĬustom Camera 7 → 45 degrees to the front left viewĬustom Camera 9 → 45 degrees to the front right viewĬustom Camera 1 → 120 degrees to the back left viewĬustom Camera 3 → 120 degrees to the back right view (we will assign the load shortcuts later below) Also make sure to click the numbers above the letters NOT the ones in the numpad. Important Note: use “LEFT” Ctrl and “LEFT” ALT. (A) Configure the first camera by positioning, for example, your view to be 45 degrees front view (you may use the free camera using the mouse to make the configuration precise including the desired zoom), then use the shortcut Ctrl+Alt+7 to save it on custom camera #7 The idea is to use one hand on the numpad of the keyboard or on the throttle buttons (as in TWCS throttle) to control the views. In the following, I’m sharing my configuration of custom cameras which made my experience much easier and enjoyable. I’m reposting it here in the public forum since the alpha forum cannot be accessed by newcomers. for details on how to configure hat switch please refer to my response to a question below in the chain of this post.Īs an alpha tester, I had several tries and I posted my setting which was liked by many.This is because I found it irritating and not natural to move from extreme left to extreme right back position with just the hat switch.I’m also sometimes using Translate key to move within the cockpit. In fact, my configuration is to use custom camera first then to use the hat switch to fine tune my view. Of course you can configure your POV/hat switch to look around inside the cockpit. Flight simulator has a robust camera system (if configured correctly). 5 blinks - encoder speed is set to 5)Ĥb (once in Encoder Speed Mode). Exit Encoder Speed Change.For a lot people, the cockpit views during navigation could be a challenge without head TrackIR / VR. The red LED will blink several times indicating the new encoder speed (i.e. The bottom red LED one the left side of the unit will light up indicating you are in Encoder Speed mode.Ĥa (once in Encoder Speed Mode).Encoder Speed Change. "Right Small Knob Press" hold for 3 seconds. However currently, if you increase beyond 5, X-Plane / MSFS will not be able to read it. This will enable to increase / decrease encoder speed mode on a scale from 1 to 10 (by default it's 5). This functionality is not for "hot swapping".ģ. Please keep in mind that you need to switch between 530 and 430 before starting the launcher and the sim. Menu +/- "Left Encoder Small Knob"ġc (once in LCD Menu Mode). Cycle through different video inputs (VGA->HDMI) ".v"ġd (once in LCD Menu Mode). Menu Enter "Left Encoder Press"ġb (once in LCD Menu Mode). The top red LED one the left side of the unit will light up indicating you are in LCD menu mode.ġa (once in LCD Menu Mode). If you have FlightSimBuilder 530 v2 (with cables on the back), there are additional functionality available:ġ. Open X-Plane folder and find you favorite airplane folder location (i.e. X-Plane 11\Aircraft\Carenado CT210M_Centurion)Ģ. If you are using Reality-XP GNS 530, you can find the instructions on how to remove bezel in the RealityXP instructions. The button on the top right corner is somewhat hidden but you can see it in the video. It will ask to replace the default file, say OK.Ĥ. If you are using with default X-Plane 530, you need to download the following file Garmin_530_2d.png (right click and select "Save Link As") and place it "\X-Plane 11\Resources\bitmaps\cockpit\radios\GPS FMS" folder. You might also need to click "Reset to defaults" once you are in x-plane control panel with FlightSimBuilder GNS 530 selected.Ī. Please download FlightSimBuilder_GNS_530.joy file and place it into \X-Plane 12\Resources\joystick configs\ folder. If for any reason you don't have the mapping in x-plane. X-Plane now has FlightSimBuilder GNS 530 mapping so no need for mapping any more.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |